Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
This article presents the results of a research developing high performance cement mortars with the addition of municipal solid waste incineration fly ash (MSWIFA) stabilized as insoluble carbonates. The encapsulation of hazardous wastes in mortar matrixes has also been achieved. The ashes present high concentrations…
Tissue engineering is a new field of knowledge which creates the possibilities for producing bioactive cardiac prostheses that will characterize by biomechanical and morphological properties similar to native tissue. It is expected that it will be characterized by high durability, which is very important from the soci…
The paper presents a new method for manufacturing hollow shafts, where tubes are used as billet. First, the design of a specially designed forging machine for rotary compression is described. The machine is then numerically tested with regard to its strength, and the effect of elastic strains of the roll system on the…
This study presents mechanical spectroscopy of bearing steel subjected to different heat treatments. A non-thermally activated maximum, P1, was found at 130°C, in quenched martensitic samples, which were austenitized at 1050°C and 860°C, and presented twin martensite microstructures. It is suggested that the mechanism…
The main aim of this work was to numerically investigate and optimize feeding and geometrical parameters to produce inlet valves of Ti6Al4V alloy that are free from defects, especially porosity. It was found that the change of geometry orientation as well as inlet feeder diameter and angle showed distinct relationship…
The paper presents results of measuring thermal conductivity of green sand mould material and time of castings solidification evaluated from cooling curves. During the experiments pure Cu (99,8 %) plate was cast into the examined sand moulds. Basing on the measurements it was stated that thermal conductivity of the mo…
This paper describes the technology of welding of finned tubes made of the X5CrNi1810 (1.4301) austenitic steel, developed at Energoinstal SA, allowing one to get high quality joints that meet the requirements of the classification societies (PN-EN 15614), and at the same time to significantly reduce the manufacturing…
Abstract The article present the results of the study on the improvement of mechanical properties of the surface layer of 7075 aluminum alloy via two-stage aging combined with shot peening. The experiments proved that thermo-mechanical treatment may significantly improve hardness and stress distribution in the surface…
The study presents the results of research into the impact of strain in cold drawing and surface modification treatment on corrosion properties of wires made of X10CrNi 18-8 steel used in maxillofacial surgery. Scanning microscopy enabled to make images of the surface of wires after drawing process as well as after su…
When optimizing the performance of constrained robotic system, the motion trajectory plays a crucial role. In this research the motion planning problem for systems that admit a polynomial description of the system dynamics through differential flatness is tackled by parameterizing the system's so-called flat output as…
The efficiency of vacuum steel degassing using RH methods depends on many factors. One of the most important are hydrodynamic processes occurring in the ladle and vacuum chamber. It is always hard and expensive to determine the flow character and the way of steel mixing in industrial unit; thus in this case, methods o…
In this research, biomechanical behaviors of five different configurations of screws used for stabilization of femoral neck fracture under axial loading have been examined, and which configuration is best has been investigated. A point cloud was obtained after scanning the human femoral model with a three dimensional…
The material subject to investigation was two commercial alloys of cobalt CoCrW (No. 27 and 28) used in prosthodontics. The scope of research included performing an analysis of microstructure and functional properties (microhardness, wear resistance and corrosion resistance), as well as dilatometric tests. The examine…
The adsorption isotherms and structural evolution of alkyl quaternary ammonium bromide (Cn TAB) on graphite oxide (GO) were measured by means of an elemental analyzer, X-ray diffraction and Fourier transform infrared spectroscopy. In order to interpret the adsorption mechanism of surfactants onto GO, the adsorption ki…
The wear behavior of Al/SiC composites prepared by stir casting technique is investigated to find out the effects of the weight percentage of SiC, load, and the number of strokes on a shaper machine. Metal matrix composite (MMC) pins are prepared with different weight percentages of SiC (10%, 15%, and 20%). The tests…
In order to understand the effect of additive Al2O3 powders on the film corrosion resistance and the microstructure of the micro-arc oxide (MAO) ceramic film of magnesium alloy, AZ91D die cast magnesium alloy was oxidized with a special micro-arc apparatus. Morphological characteristics and phase constituent of cerami…
Achieving fast and strong adhesion to jawbone is essential for dental implants. Thin deposited films may improve osseointegration, but they are prone to cohesive and adhesive fracture due to high stresses while screwing the implant into the bone, leading to bared, less osteoconductive substrate surfaces and nano- and…
The Devonian micritic limestones from the Prague Basin (Barrandian area, Bohemian Massif, Czech Republic), which were the primary raw material used for natural hydraulic lime burned in Prague, exhibit a feebly to eminently hydraulic character. Based on a laboratory experimental study, the burned product is composed of…
Electron back-scattered diffraction (EBSD) studies carried out for the Cu/α−Al2O3 composites manufactured by pulsed laser deposition method and by the powder metallurgy enable to uncover a set of orientation relationships characteristic for materials of this type. The identified interfaces are categorized according to…
Abstract The paper presents the problem of obtaining a permanent diffusional joint between the working surface layer and the base part in a bimetallic casting. The studied bimetallic casting was obtained as a result of using the founding method of layer coating directly in the cast process. The casting prepared using…