Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
The electrical conductivity and dielectric properties of nanocrystalline zinc ferrite with various grain sizes ranging from 7 to 115 nm have been studied over a wide frequency range 1 Hz–15 MHz by impedance measurements in the temperature range of 300–650 K. The effect of grain size on the conductivity has been invest…
Utilizing refrigeration may provide the only means by which future high-performance electronic chips can be maintained below predicted maximum temperature limits. Widespread application of refrigeration in electronic packaging will remain limited, until the refrigerators can be made sufficiently small so that they can…
Duplex stainless steels, with ferritic-austenitic microstructure, have excellent mechanical properties and corrosion resistance. However, when duplex stainless steels are exposed to temperatures between 600 and 1000 °C, some phase transformations can occur such as chromium nitrides precipitation, chromium carbides pre…
The phenomenological formalism, which yields Fick's Laws for diffusion in single phase multicomponent systems, is widely accepted as the basis for the mathematical description of diffusion. This paper focuses on problems associated with this formalism. This mode of description of the process is cumbersome, defining as…
An Al-5SiO2 (5 wt% of SiO2) aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si)/Al2O3 interlaced struc…
Theoretical determination of the ground-state geometry of Si clusters is a difficult task. As the number of local minima grows exponentially with the number of atoms, to find the global minimum is a real challenge. One may start the search procedure from a random distribution of atoms but it is probably wiser to make…
A nuclear reactor pressure vessel steel was submitted to different quenching and tempering heat treatments aimed at simulating neutron irradiation damage. The obtained microstructures were mechanically tested and submitted to metallographic and fractographic survey. The relevant microstructural and fractographic aspec…
Aluminophosphate sieves with AFI structure substituted by Ti (denominated TAPO-5) have been synthesized hydrothermally. These materials were characterized by X-ray diffraction (XRD), chemical analysis (ICP), scanning electronic microscopy (SEM), ultraviolet diffuse reflectance spectroscopy (DRS-UV) and thermogravimetr…
The attainment of finer ferrite grain structure in low carbon is object of interest because significantly higher yield strengths and lower ductile-brittle transition temperatures can be predicted at the same time with ultra-fine grain sizes. This work verified the microstructural evolution of a low carbon 0.15%C-1.39%…
Dry sludge from the Sabadell Water Treatment Plant was used to prepare prefabricated concrete bricks. After characterising the sludge and the manufacturing process used to make the bricks, we define the conditions of addition of the sludges in the manufacture. Reference samples not containing sludge and samples contai…
The causes of the pathologies found on the lime renderings from Plaza de la Corredera façades are analysed in this study. For this purpose, the mineralogical and chemical analyses of the building materials -brickwork and rendering mortar- has been carried out, as well as their physical, hydric and mechanical propertie…
Cu and Fe species formed during the preparation of Cu/ and Fe/ZSM-5 catalysts by ion exchange were studied. XRD, SEM, H2-TPR, DRS-UV-VIS, EPR, Mössbauer Spectroscopy (MÖSS) and chemical analysis (AAS) were used to sample characterization. Cu/ZSM-5 catalysts, irrespective of their Si/Al ratio and Cu content, showed a r…
Thermodynamic calculations of the Fe-Cr-N System in the region of the Gas Phase Equilibria have been compared with experimental results of maximum nitrogen absorption during nitriding of two Martensitic Stainless Steels (a 6 mm thick sheet of AISI 410S steel and green powder compacts of AISI 434L steel) under N2 atmos…
The results of an experimental investigation on the microcracking of high-performance concrete subjected to biaxial tension-compression stresses are presented. Short-term static tests and microcracking mapping were performed on 12.5 cm square by 1.25 cm thick plates. Strain controlled tests were executed in a biaxial…
This paper discusses the effects of carbonation on the microstructure of Portland cement concrete for long-term durability applications. A class C40 concrete (characteristic compression strength between 40 MPa and 44 MPa on the 28th day, according to Brazilian standard NBR 8953) was chosen for the experimental study o…
The pozzolana activity is the main property of the active additions but, in order to select them, we have to consider - between other factors- its mineralogical composition with a great influence, not only in the active component, but also in other cement properties. In the present work we have studied 4 different Cub…
We have developed a method to obtain polymer hybrids with control of inorganic content and molecular configuration. Hybrid poly(methyl methacrylate) (PMMA) was obtained via atom transfer radical polymerization (ATRP) initiated by octafunctional cubic silsesquioxanes using CuCl as catalyst. Two different ATRP initiator…
The durability and chemical resistance of alkali activated slag and fly ash/slag mortars in contact with sulfates and seawater media have been studied. Two methods were used in the evaluation of such durability: Kock-Steinegger and ASTM C1012. A mineralogical and a microstructural characterization of mortars were done…
For thirty years it has been known that certain compositions of Na2O-CaO-P2O5-SiO 2 glasses will form a mechanically strong, chemical bond to bone. These materials have become known as bioactive glasses and the process of bonding is called bioactive fixation. Bioactive glasses are widely used clinically in the repair…