Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Natural sand mining from rivers and seashores is causing serious environmental problems in many parts of the world, whereas the fine fraction from recycling concrete waste is underutilized as a construction material. The aim of this paper is to determine the maximum replacement level of natural sand by recycled sand i…
In this study the research on deformability of AlMg alloys with high Mg contents in extrusion was carried out. The different shapes from AlMg alloys containing 3.5%, 4.5% and 5.5% of Mg were extruded on 500 T semi-industrial press by using one-hole and multi-hole flat dies. The extrudates surface quality was under inv…
The authors own computer software, based on the Ueshima mathematical model with taking into account the back diffusion, determined from the Wołczyński equation, was developed for simulation calculations. The applied calculation procedure allowed to determine the chemical composition of the non-metallic phase in steel…
For the past two decades, atomic force acoustic microscopy (AFAM), an advanced scanning probe microscopy technique, has played a promising role in materials characterization with a good lateral resolution at micro/nano dimensions. AFAM is based on inducing out-of-plane vibrations in the specimen, which are generated b…
Zn-Al-Cu alloys are used primarily because of their tribological properties as an alternative material for bronze, cast iron and aluminum alloy bearings and as a construction material. Particularly interesting are high aluminum zinc alloys. Monoeutectic zinc and aluminum alloys are characterized by the highest hardnes…
Problem of Post-operative infections of implant materials caused by bacterial adhesion to their surfaces is very serious. Enhancement of antibacterial properties is potentially beneficial for biomaterials value. Therefore, the metallic and metallic oxide nanoparticles attract particular attention as antimicrobial fact…
Pure aluminium (6N) and commercially pure aluminium (99.7) was deformed by KOBO method. Microstructure and texture of both materials after deformation was analyzed by means of scanning and transmission electron microscopy. Advanced methods of crystallographic orientations measurements like Electron Backscatter Diffrac…
In this study, Ni, Ni-SiC and Ni-Al2O3 coatings were electroplated on the 2xxx series aluminium alloy. The following parameters of the electroplating process were applied: current density - 4A/dm2, time - 60 minutes, and temperature - 60°C. Hard particles of submicrometric size were used. The results of the research s…
The synthesis of porous metal-oxide semiconductors for gas-sensing application is attracting increased interest. In this study, α-Fe2O3 hollow balls were synthesized using an inexpensive, scalable, and template-free hydrothermal method. The gas-sensing characteristics of the semiconductors were systematically investig…
The following is the text of an oral presentation delivered at the Zener Medal Award ceremony in Hefei on 23 September 2015.
The resultes of anodic oxide conversion coatings on wrought AZ61 magnesium alloy production are describe. The studies were conducted in a solution containing: KOH (80 g/l) and KF (300 g/l) using anodic current densities of 3, 5 and 10 A/dm2 and different process durations. The obtained coatings were examined under a m…
We demonstrated a metamaterial absorber (MMA), which can be controlled by variation of conductivity or temperature. The metamaterial (MM) structure is based on three individual layers of periodic split ring resonator (SRR), a dielectric, and metallic film. The resonant frequency of the designed structure is numericall…
Mechanical properties at elevated temperature, in modern alloys based on intermetallic phase Ni3Al are connected with phase composition, especially with proportion of ordered phase γ′ (L12) and disordered phase γ (A1). In this paper, analysis of one key systems for mentioned alloys - Ni-Al-Cr, is presented. A series o…
The effect of process parameters of conversion coatings on the corrosion resistance was investigated. To produce anodic coatings, the solutions of H2SO4 of 0.5 and 1 M concentrations and current densities of 0.5 and 1 A/dm2 were applied. The coatings were deposited by galvanostatic technique on titanium Grade 1. The r…
Condition monitoring of deterioration in the metallurgical equipment is essential for faultless operation of the metallurgical processes. These processes use various metallurgical equipment, such as induction motors or industrial furnaces. These devices operate continuously. Correct diagnosis and early detection of in…
The results of studies carried out on the heat treated AZ61 magnesium alloy extruded by two methods, i.e. direct extrusion and continuous rotary extrusion, were presented. As part of the work, parameters of the T6 heat treatment were proposed and aging curves were plotted. The solution heat treatment process was accom…
CoxPt100−x nanoparticles (x = 50, 59, and 73) were prepared by the chemical reduction of Cobalt (II) chloride and Chloroplatinic acid, then ultrasonicated for 2 h. After annealing at various temperatures from 450 °C to 700 °C for 1 h, structure change was observed and samples show hard magnetic properties which depend…
Recycled aggregate (RA) from construction and demolition waste is traditionally used for the manufacture of concrete for different applications. Due primarily to high water content required by RA, the quality of the concrete is determined by the amount of replacement RA. The aim of this study is to determine if RA pre…
Imitating the structure of steel-reinforced concrete, a composite coupling good damping capacity and mechanical property was fabricated by pressure infiltration progress. The aluminum (Al) matrix composite was hybrid reinforced by 20% volume fraction of SiC particle (SiCp) and 20% volume fraction of TiNi fiber (TiNif)…
This paper presents the mechanical performance and durability of concrete with water/cement (w/c) ratios of 0.30 and 0.60 containing cactus mucilage and brown marine seaweed extract solutions (at 0.5° Brix concentrations). Cylindrical specimens (100 mm x 200 mm) were cast and moist-cured for 0 and 28 days. Compressive…