Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Gold nanoparticles coated by gadolinium (III) chelates (Au@DTDTPA) where DTDTPA is a dithiolated bisamide derivative of diethylenetriamine-N,N,N',N'',N''-pentaacetic acid (DTPA), constituted contrast agents for both X-ray computed tomography and magnetic resonance imaging. In an MRI context, highly stable Gd(3+) compl…
ABSTRACT The main objective of this study was to assess the effect of two amino resins, N ‐methylol melamine (NMM) and 1,3‐dimethylol‐4,5‐dihydroxyethyleneurea (DMDHEU), on the intrafiber and interfiber strengths and water absorption of two types of waste paper categories, office paper (OP), and old corrugated contain…
Conventional equal channel angular pressing is an efficient technique to obtain bulk ultrafine grained materials (UFG) with extraordinary mechanical properties in the form of rods. In this work, an incremental method of ECAP process which allows to obtain thick sheets with UFG structure is presented. Using this method…
A body-centred cubic (BCC) structure metal, tantalum, was processed by high- pressure torsion (HPT) at room temperature with different numbers of rotations. The microstructural evolution was studied by electron backscatter diffraction (EBSD). The grain sizes were significantly refined at the disk edge area in the earl…
This paper reports results on the effect of interaction of Ag(+) on 1D droplet array spacing and the repulsive forces between stimuli-responsive nanoemulsion droplets, stabilized with an anionic surfactant--sodium dodecyl sulfate--and a diblock polymer--poly(vinyl alcohol)-vinyl acetate. The repulsive interaction is p…
The development of nanocrystalline structures in austenitic stainless steels during large strain cold rolling and their tensile behavior were studied. The cold rolling to total equivalent strains above 2 was accompanied by the evolution of nanocrystalline structures with the transverse grain size of about 100 nm. The…
CuCrZr alloys exhibit very good relation between mechanical properties and electrical conductivity. However, for its use in some advanced applications improvement of mechanical strength while preserving high electrical conducting is required. Therefore, in this work a CuCrZr alloy was subjected to a series of thermo-m…
Large billets (5 x 5 x 30) cm 3 of technically pure aluminum (AA 1050) taken from thick rolled sheets were deformed at room temperature by single pass equal-channel angular pressing (ECAP). ECAP was done at different back pressures (0 – 60 MPa) using a square die with channels intersecting at 90° in sharp corners. The…
We calculated the susceptibilities of BaTiO3 by molecular dynamics (MD) simulations using an isotropic shell model of Tinte et al. (S. Tinte, M.G. Stachiotti, S.R. Phillpot, M. Sepliarsky, D. Wolf, and R.L. Migoni, Ferroelectric properties of BaxSr1-xTiO3 solid solutions obtained by molecular dynamics simulation. J Ph…
Ti-6Al-4V alloy is an advanced structural material having applications in a wide range of areas spanning from biomedical to aerospace sectors due to the excellent combination of mechanical and chemical properties. In the present work, a new tailored heterogeneous microstructural design with a specific topological dist…
ABSTRACT In this article, a composite film from polyimide and thermally exfoliated graphene was prepared through in situ polymerization, and the weight percent of thermally exfoliated graphene with respect to the polyimide monomers was 5 wt %. The film was carbonized at 1000°C for 1 h and then heat‐treated at various…
A simple method to produce pure carbon nanosphere (CNS) in high yield using continuous chemical vapor deposition (CVD) technique (combination of floating catalyst CVD and fluidized bed CVD) is proposed. Carbon fiber substrate, acetylene precursor, and Fe catalyst are employed to produce CNS. X-ray diffraction (XRD) an…
Mesoporous barium titanate (BT) thin films are synthesized by a surfactant-assisted sol-gel method. The obtained mesoporous BT thin films show enhanced ferroelectricity due to the effective strains induced by mesopores. The Curie temperature (T(c)) of the mesoporous BT reaches approximately 470 °C.
In this study, a developed temporal focusing-based femtosecond laser system provides high-throughput multiphoton-induced reduction and ablation of graphene oxide (GO) films. Integrated with a digital micromirror device to locally control the laser pulse numbers, GO-based micropatterns can be quickly achieved instantly…
Silicon carbide quantum dots in the size range of 1–10 nm are in the center of interest with unique properties that makes them very promising biomarkers. A central requirement for this application is the control over the complex structure of the surface to enable further surface functionalization processes, which are…
The influence of severe plastic deformation on strength and electrical conductivity in the Cu-Cr copper alloy has been studied. Microstructure of ultrafine-grained samples was investigated by transmission electron microscopy and X-ray diffraction with special attention on precipitation of small chromium particles afte…
Accumulative roll bonding (ARB) was applied to three FCC metals, such as Al, Cu and Ni. Differential scanning calorimetry (DSC) and X-ray diffraction (XRD) were made to evaluate dislocation density ρ of the ARB processed FCC metals. The values of ρ of ARB processed Cu and Ni increased rapidly after the first ARB cycle…
In this study, Al-2%Fe samples extracted from a cast ingot in the shape of rings were processed by High-Pressure Torsion (HPT) at room temperature. Suitable specimens were extracted for evaluation of mechanical properties and electrical resistivity. High tensile strength of ~600 MPa was attained by HPT due to grain re…
The nanoparticles composed of Mg and Pd atoms (Mg–Pd NPs) have been fabricated by the gas evaporation method, and the variation of the chemical state during hydro‐/dehydrogenations has been investigated by X‐ray photoelectron spectroscopy (XPS) and in‐situ X‐ray absorption fine structure (XAFS) analyses. Both XPS and…
Abstract. The Université de Lorraine in Metz, France, is the selected site for the 6th International Conference on Nanomaterials by Severe Plastic Deformation (NanoSPD6) following a series of five earlier conferences. This introductory paper reports on several major developments in NanoSPD activities as well as on ver…