Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
In this study, TIG welding was used to clad and repair the surface of cast AZ91C magnesium alloy. Then, friction stir processing and T6 heat treatment wrer applied on the welded region. Microhardness results showed an improvement in the mean hardness of welded zone and also FSPed zone. Increase in the mean microhardne…
The present research reports on the results of some experiments dealing with the recycling of steel scale waste in the production of mortars. Materials were prepared mixing a commercial CEMII/B-LL cement, a steel scale waste, a commercial natural aggregate, superplasticizer and water. Natural aggregate was replaced wi…
The longitudinal-field muon-spin relaxation (LF-μSR) technique was employed to study the spin correlations in (Mn,Fe)2(P,Si) compounds above the ferromagnetic transition temperature (TC). The (Mn,Fe)2(P,Si) compound under study is found to show itinerant magnetism. The standard deviation of the magnetic field distribu…
A numerical analysis is performed of the stress field in and around inclusions of various shapes. Inclusions both stiffer and more compliant than the metal matrix are analysed. The critical stresses required for inclusion fracture are estimated after observation of cavities and inclusions by scanning electron microsco…
Abstract In this study, chitosan coatings were electrophoretically deposited (EPD) on near-β Ti-13Nb-13Zr alloy. The influence of colloidal solution composition and EPD parameters on the quality of chitosan coatings was investigated. It was established that the uniformity of as-deposited chitosan coatings is highly de…
Industrial robots are most often position controlled and insensitive to external forces. In many robotic applications, however, such as teleoperation, haptics for virtual reality, and collaborative robotics, a close cooperation between humans and robots is required. For such applications, force sensing and control cap…
The valence instability in lanthanide systems is described within an extended periodic Anderson Hamiltonian (EPAM) which includes Coulomb repulsion between f- and conduction- electrons, allowing to describe both discontinuous and continuous valence variations. We investigate the connection between valence and magnetis…
Abstract The cracking of materials and fracture surface is of great practical and academic importance. Over the last few years the development of the fractography of crystalline alloys resulted in a useful tool for the prediction or failure analysis. Many attempts have been made to observe cracks using optical microsc…
Abstract The paper presents formulas used to calculate critical temperatures of structural steels. Equations that allow calculating temperatures Ac 1 , Ac 3 , Ms and B s were elaborated based on the chemical composition of steel. To elaborate the equations the multiple regression method was used. Particular attention…
Abstract A2B2O7 oxides with pyrochlore or defected fluorite structure are among the most promising candidates for insulation layer material in thermal barrier coatings. The present paper presents the procedure of synthesis of holmium zirconate Ho2Zr2O7 and praseodymium zirconate Pr2Zr2O7 via Polymerized-Complex Method…
Abstract The goal of the research carried out was to develop the fuzzy systems, allowing the determination of the Jominy hardenability curve based on the chemical composition of structural steels for quenching and tempering. Fuzzy system was created to calculate hardness of the steel, based on the alloying elements co…
The SiO2 and Ni/SiO2 coatings were electrophoretically deposited on X2CrNiMo17-12-2 steel using ethanol-based suspensions of the SiO2 and Ni powders. The influence of the zeta potential and concentration of the suspensions, the applied voltage and deposition time on the quality of the coatings was studied. Microstruct…
Abstract The aim of the work was to perform adequate selection of the phase composition of the composite designated for permanent - mould casting air compressor pistons. The hybrid composites based on AlSi7Mg matrix alloy reinforced with mixture of silicon carbide (SiC) and glassy carbon (Cg) particles were fabricated…
In order to improve the tribological properties of titanium alloy Ti6Al4V composite surface layers Ti/TiN were produced during laser surface gas nitriding by means of a novel high power direct diode laser with unique characteristics of the laser beam and a rectangular beam spot. Microstructure, surface topography and…
UH 3 based hydrides with modified structure and composition can be prepared using high H 2 pressures from precursors in the form of rapidly cooled uranium alloys. While the alloys with α-U structure lead to the β-UH 3 type of hydrides, γ-U alloys ( bcc ) lead either to α-UH 3 hydride type or nanocrystalline β-UH 3 . T…
Marble industry produces large amount of waste during mining and processing stages. This waste is dumped on to open land which creates a lot of environmental problems. The main objective of this study was utilization of marble waste as a replacement for conventional natural coarse aggregate in concrete. Experimental i…
An optimal method for composites preparation as an input to rapid prototyping fabrication of scaffolds with potential application in osteochondral tissue engineering is still needed. Scaffolds in tissue engineering applications play a role of constructs providing appropriate mechanical support with defined porosity to…
We have studied the magnetic properties of a LuVO 3 single crystal . The compound shows an orbital ordering at T OO = 179 K followed by the antiferromagnetic spin ordering at T SO = 109 K. In the magnetically ordered regime, there appears an abrupt change at T o = 82.5 K in the magnetisation, indicating a first-order…
Abstract This paper presents the research results of the balls rolling process according to the conventional and modified methods of rolling. Theoretical analysis was carried out by using numerical methods based on the Finite Element Method. The Simufact package version 10.0 were used for calculation. Simulations of b…
In this study, microstructure and mechanical properties of diffusion joints between 5754, 6061 and 7039 aluminum alloys and AZ31 magnesium alloy were investigated. Diffusion joints were done between the alloys at 440 °C, for duration of 60minutes, at 29 MPa pressure and under 1×10-4 torr vacuum. The interface of joint…