Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Fatigue fracture often occurs because of the corrosion damage to aerospace structural aluminum alloy with holes. Fatigue tests of 7075 aluminum alloy of both unchamfered and chamfered double-hole specimens under uncorrosion and 24h pre-corrosion were carried out. The influence of both pre-corrosion damage and orifice…
The tungsten carbide coating with both high hardness and dense microstructure was prepared by optimizing the detonation gun spraying parameters. The phase identifications and microstructure of the coating were observed and analyzed by optical microscope, X-ray diffraction (XRD) and energy dispersive spectrometer (EDS)…
A primer of the bismaleimide resin toughened with block copolymer was prepared. The properties of the primer, such as adhesion, pencil hardness, impact resistance, environment resistant, ageing resistant performance and etc. meet the requirements of the technical specifications of GJB1388. The thermal property of the…
The microstructure and property degradation of turbine blades in aircraft engines during service would finally pose threat to service safety. But report on systematic research work about microstructure and property degradation of serviced turbine blades is limited. In this paper, the 2nd stage turbine blade made of wr…
As-cast microstructures and phase compositions of Mg-3.52Sn-xM and Mg-6.54Sn-xM (M=Al, Zn, Nd, Gd) alloys were investigated by optical microscope, scanning electron microscope and X-ray diffraction. Meanwhile, the tensile mechanical properties were tested. The results show that the coarse dendrite is refined slightly…
Abstract The aim of this work was to study the microstructure and functional properties of CuNi2Si1 alloy. The material was prepared classically by melting, casting, hot rolling and cold rolling. The obtained strips were processed with combined operations of supersaturation, ageing and one of the intensive deformation…
Abstract The presented work focuses on the quantitative description of the spinel phase (NiAl2O4) located into Al2O3matrix. Three series of samples were prepared. Series I, II and III containing following amount of nickel powder: 0.21% vol, 0.43% vol and 1.3% vol respectively. In order to obtain nickel aluminate spine…
Twin Roll Casting technology belongs to modern, integrated method of processing aluminum and its alloys. This method includes preparation of liquid metal and its continuous casting between the rotating cylindrical crystallizers, optional homogenizing treatment, cold rolling and optional interoperation or final heat tr…
Abstract The article presents the possibility of using twin-spot laser welding (i.e. laser welding with focusing a laser beam on two spots) for making overlap joints made of 0.8-1 mm thick HSLA and DP type high strength steel sheets. Joints were made using a Yb:YAG disc laser having a maximum power of 12 kW and a weld…
The coatings of FeAlCuCrCoMn high entropy alloy were deposited by direct current magnetron sputtering. The microstructure and the mechanical and corrosion properties of the coatings are investigated. A perfect dense and smooth coating could be obtained. The coatings exhibit single FCC solid solution as increasing depo…
Abstract Mixed ionic and electronic conducting K2NiF4-type oxide, Nd2Ni1-xCuxO4+δ (x=0~1) powders were synthesized by solid state reaction technique and solid oxide fuel cells consisting of a Nd2Ni1-xCuxO4+δ cathode, a Ni-YSZ anode and ScSZ as an electrolyte were fabricated. The effect of copper substitution for nicke…
In this study, NBG was successfully achieved through a sol-gel technique, and to further improve its dispersibility, a crylate coupling agent was coupled onto the surface of the NBG. The 3-(Trimethoxysilyl)Propylmethacrylate coupling agent was used to the surface modification of the synthesized NBG by a wet-chemical m…
In the study microstructure and properties of composite multifibre copper-base wires are presented. A decision was made to produce wires with “soft” fibres (Al) and “hard” fibres (Fe). In the study the phenomenon occurring on the border of Al-Cu was also analysed. The produced Cu-Al and Cu-Fe composites presented orde…
Abstract In the paper the results of metallographic examination and mechanical properties of electron beam welded joint of quenched and tempered steel grade S690QL are presented. Metallographic examination revealed that the concentrated electron beam significantly affect the changes of microstructure in the steel. Par…
Abstract The investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution suppo…
This paper presents results of failure analysis study to characterize the corrosion damage that occurred in the water supply system in Krakow. This analysis includes: electrochemical noise, linear polarization and resistometric measurements. Water aggressiveness of four water intakes was defined using Langelier and Ry…
We prepare and optically characterize a thin film of GaN:Eu. Room temperature intense emission band at around 620 nm is observed, corresponding to 5D0 → 7F2 electronic dipole transition of Eu3+ ions in the GaN host material. At lower temperatures, three components, at 621, 622, and 623 nm, arising from different Eu3+…
Wrapping technology is one of the effective ways of strengthening concrete elements. Several researchers reported the effectiveness of Glass fiber reinforced polymers and carbon fiber reinforced polymers for improving the strength of the concrete elements. Wrapping on three sides is one of the effective methods for st…
Abstract Cementation of tin on copper in acid chloride-thiourea solutions leads to the formation of porous layers with a thickness dependent on the immersion time. The process occurs via Sn(II)-Cu(I) mechanism. Chemical stripping of tin was carried out in alkaline and acid solutions in the presence of oxidizing agents…
Abstract Problem of post-operative infections of implant materials caused by bacterial adhesion to their surfaces is very serious. Enhancement of antibacterial properties is potentially beneficial for biomaterials value. Therefore, the metallic and metallic oxide nanoparticles attract particular attention as antimicro…