Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Metastable phase characteristics of beta Ti alloys were investigated to consider the relationship of the microstructureand diffraction pattern in TEM. TEM analysis showed that the microstructure was mottled as a modulated structure, and thediffraction pattern was composed of spot streaks between the main spots of a st…
D Kaoumi, T Gautier, J Adamson, M Kirk; Using In-Situ TEM to Characterize the Microstructure Evolution of Metallic Systems under External Solicitation, Mic
D Edwards, N Erdman, D Guarrera, M Shibata, V Robertson, F Timischl, Y Nemoto; Advantages of Beam Deceleration for Low kV EDS Analysis, Microscopy and Micr
Jun-Fu Liu, Mel J Esmacher, David Kotwica; Denickelification and Dezincification of Copper Alloys in Water Environments, Microscopy and Microanalysis, Volu
AJ D’Alfonso, SD Findlay, LJ Allen; Simulating Inelastic Scattering in Scanning Transmission Electron Microscopy using μSTEM, Microscopy and Microanalysis,
Chang Wan Han, Paulami Majumdar, Ernesto E Marinero, Antonio Aguilar-Tapia, Rodolfo Zanella, Jeffrey Greeley, Volkan Ortalan; In situ Environmental TEM and
Ute Schmidt, Olaf Hollricher, Wei Liu, Edward L Principe; RISE Microscopy: Correlative Raman and SEM Imaging, Microscopy and Microanalysis, Volume 21, Issu
Gregory B Thompson, Monica Kapoor, Tyler Kaub, Brad Boyce, Blythe Clarke, Kris Darling, Peter Felfer, Julie Cairney; Investigation into Solute Stabilizing
B C Regan, William A Hubbard, E R White, Rohan Dhall, Stephen B Cronin, Shaul Aloni, Matthew Mecklenburg; Introduction to Plasmon Energy Expansion Thermome
Bethany M Hudak, Yao-Jen Chang, Lei Yu, Guohua Li, Danielle N Edwards, Matthew E Park, Beth S Guiton; Understanding nanomaterial synthesis with in situ tra
An atmospheric pressure plasma jet (APPJ) technique was developed to functionalize amino groups to obtain plasma-functionalized carbon nanotube (CNT) dot-array as a precursor of biomolecules of the bio-chip sensor. To realize bio-chip sensors based on CNT, it is needed the proper control of their surface functionaliza…
Abstract We shall be concerned with the buckling of a thin circular elastic plate simply supported along a boundary, subjected to a radial compressive load uniformly distributed along its boundary. One of the main engineering concerns is to reduce deformations of plate structures. It is well known that von Kármán equa…
OBJECTIVE: To evaluate the effect of aging of the composite and the adhesive interface on composite-composite repair bond strength. METHODS: Methacrylate-based composite resin (Clearfil AP-X, composite A) and silorane-based composite resin (Filtek P90, composite B) and their corresponding adhesive, Clearfil SE Bond (a…
The influences of the two kinds of floating conductor defects, plate-needle-plate and needle-needle-plate, on the partial discharge are investigated. For the plate-needle-plate structure, the discharge is initiated from the suspended needle conductor, and two kinds of discharges, corona and partial breakdown, are prod…
Nerve cuff electrodes for peripheral nerve prostheses are required chronically implanted electrodes which simultaneously stimulate and record nerve activity. It is inevitable challenge to investigate electrode material with low interfacial impedance and enhanced charge transfer capacity. In this study, stimulus nerve…
A displaced thermal state (DTS) is first introduced by Jeong et al. [Phys. Rev. Lett. 97, 100401 (2006)] and its superpositions can be used in transfer of nonclassicality. In this paper, the analytical evolution law of the DTS exposed to dissipative environments is obtained according to the Kraus operator for amplitud…
The effect of gallium-promoted copper-based catalysts has been investigated in connection with the characteristic of the active copper phase. CuO-ZnO-Ga2O3catalysts with different gallium loadings were prepared using oxalate co-precipitation method. The effects of gallium loading on the properties of catalysts were st…
In order to make the specimen deformed under a constant strain rate and the stress in the specimen kept homogeneous, the wave shaper technology was adopted to modify the incidence waves of the normal Split Hopkinson Press Bar. A method of changing the shape of the bullet was suggested to be applied on the SHPB. Bullet…
MAT224 is a tabulated version of the Johnson-Cook model in LS-DYNA. Compared with the original Johnson-Cook material, MAT224 was developed to simulate the dynamic response of a material by just defining the effective stress as a function of effective plastic strain at different strain rates and temperatures, thus avoi…
Xinming Zhang, Tao Hu, Jorgen F Rufner, Thomas LaGrange, Geoffrey H Campbell, Enrique J Lavernia, Julie M Schoenung, Klaus van Benthem; Metal/ceramic Inter