Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
A combination of poly(diphenylmethane diisocyanate) (PMDI) and stearic anhydride was investigated as a new compatibilizer system for improving the interfacial adhesion between wood and polyethylene (PE). The treatment of wood flour with PMDI increased both the modulus-of-rupture (MOR) and the modulus-of-elasticity (MO…
Liposomes are known to be taken up by the liver cells after intravenous injection. Among the few techniques available to follow this process in vivo are perturbed angular correlation spectroscopy, nuclear magnetic resonance spectroscopy, and scintigraphy. The study of the intracellular pathways and liposomal localizat…
The trace additions of Ag to binary Al-Mg alloys promote precipitation of a phase in the under-aged condition. The structures of the phase in an Al-10 Mg-0.5 Ag (mass%) alloy have been characterised using transmission electron microscopy and electron microdiffraction. An icosahedral quasicrystalline phase, which is id…
A well-defined compositionally-equivalent linear analog to a previously reported hyperbranched fluoropolymer (HBFP) was synthesized and each was subjected to characterization studies as a fundamental investigation of the role of architecture on solution and solid-state properties. Condensation polymerization of 3-{[(t…
Sodium niobate based ceramics doped with Mn atoms have been sintered from oxides. The Bi co-dopants were introduced to increase the solubility limit for Mn atoms. Two series of samples were heated at lowered air pressure to produce oxygen nonstoichiometry. X-ray Absorption Near Edge Structure (XANES) spectra at Mn K-e…
Polyacrylonitrile fibers were electrospun yielding diameters in the range of 50 to 200 nm. These nanofibers were then immersed in an aqueous coating solution to deposit a continuous film of titanium dioxide on the surface. In order to shorten the coating time and optimize the metal oxide layer thickness, the fibers we…
To control the interactions between surfaces and biological systems, it is common to attach polymers, proteins, and other species to the surfaces of interest. In this case, surface modification of polydimethylsiloxane (PDMS) was performed by exposing PDMS films to the effluent from a microwave ammonia plasma, with a g…
The characteristics of corrosion inhibitors of the tolitriazole (TTA) for the carbon steel 1008, covered by zinc or tricationic phosphate (Mn, Zn, Ni), in the means of H 2 SO 4 0.1 mol L -1 and NaCl 0.5 mol L -1 , were investigated by physical and electrochemical methods. The results obtained in the absence of the ini…
The tribochemical treatment of glass and grains surface area as a crystallization activating factor and its influence on the crystal phase formation is a subject of the study. Sheet glass SiO2–CaO– Na2O as a material of extremely small crystallization ability has been used in the investigations. Tribochemical activati…
The leather industry is categorized as a polluting industry because of the large chemical usage and the generation of solid wastes. It is estimated that as much as 62-75% of the skins appears as solid waste. Fleshings generated in the liming process constitute 50-60% of the total solid waste generated in the industry.…
Abstract This article examines the high-temperature oxidation of silica-forming ceramics under constant temperature and cyclic conditions. The effects of water vapor, impurities, and molten salts are discussed. The article describes the oxidation and corrosion of silica-forming composites, oxide ceramics, non-silica f…
Abstract The effect of the acidity of the environment on the topography and photophysics of sensitizer molecules in homogeneous solutions, and when embedded in a lipid microenvironment, was studied. Four hematoporphyrin (HP) analogs were studied, which have chemical “spacers” of varying lengths between the chromophori…
The data base on the corrosion behavior of Zr alloy materials under BWR conditions was evaluated with respect to the burnup target of 70 MWd/kgU. At high bumups, corrosion rate and the rate of hydrogen pickup (HPU) may increase. This onset of increase obviously depends on the material, but also seems to be significant…
The structure and properties of Cu-Cr-Zr alloy were studied after rapidly solidified aging and solid solution aging.At the early stage of aging (500℃ for 15 min), the hardness and the conductivity of the alloy rapidly solidified are 143 HV and 72% IACS, respectively. Under the same aging condition, the hardness and el…
The sol-gel-derived materials can be exploited for the number of applications, including biomaterials and measuring techniques. One of the most important applications involves production of sol-gel coatings. In this study, silica based sol-gel materials were prepared by way of acid hydrolysis with alcohol as a solvent…
Numerical analyses of birdstrike were performed on aircraft light structures made up in metallic, composite and polymeric materials, using the ESI/Pam-Crash solver code. The finite element models were developed calibrating the material models to take into account the different inelastic behaviours and failure modes. T…
Abstract: The aim of the present paper is to propose a method of laboratory tests to determine non-linear elastic properties of coated Panama fabric. The material parameters are specified on the basis of uniaxial tensile tests in the warp and weft directions. Techniques based on the least squares’ methods are used in…
The long-term stability of anode supported solid oxide fuel cells (SOFCs) was investigated as a function of operating temperature and current density. The largest degradation rate was observed at the lower operating temperature and higher current density of 750°C and 0.75 A/cm 2 , respectively. Detailed characterizati…
The physical and thermal properties of P2O5-Al2O3-BaO-La2O3 glasses were investigated. The effects of glass compositions on the transition temperature, thermal expansion coefficient, density, hardness and refractive index of glasses were studied. The highest hardness of the glasses is 4143.891 MPa and the lowest therm…
The first part of a corrosion inhibitor model has been developed to be used in a specific Mexican Power Plant. The model takes into account the main operational conditions found in the cooling water, such as major corrosive chemical species, a wide pH range, the performance of a commercial corrosion inhibitor (based o…