Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Two groups of cobalt nanoparticles with spherical and disk shape were used to grow carbon single-walled nanotubes by chemical vapor deposition. To elucidate the synthesis conditions and for comparison purpose, a third group of cobalt catalyst prepared by common wet chemistry was used. After the synthesis, electron-mic…
Indium tin oxide (ITO) films deposited with single layers of monodispersive fluorine-doped tin oxide (FTO) nanoparticles of several nanometers in size were grown on glass substrates by intermittent spray pyrolysis deposition using conventional atomizers. These films have significantly higher ionization potentials than…
Use of anodic bias improves the charge-injection limits of activated iridium oxide (AIROF) microelectrodes. Asymmetric waveforms, in which the charge balancing anodic phase is delivered at a lower current density and longer pulse width, has been found to allow for higher values of anodic bias voltages, thus maximizing…
Using nanoporous media as templates for electrodeposition, we have fabricated multilayered Pb∕Cu nanowires 50nm in diameter and 20μm long with Cu layer thicknesses as low as 10nm. This was achieved by using a single-bath technique and a precise selection of the copper deposition potential to limit the redissolution of…
Abstract Summary: A new siloxane colloid was developed, for the use in UV‐curable inorganic‐organic hybrid films. The UV‐crosslinkable silica‐colloids were prepared from vinyltrimethoxysilane (VTMS) via a sol‐gel method. The structure of silica‐colloids was characterized using 1 H NMR, 29 Si NMR, FT‐IR, and matrix‐ass…
Fuel cells offer potentially attractive alternative backup power solutions for telecom applications. In order to intelligently assess different fuel-cell alternatives, one needs to understand the major types of fuel cells and their current state of development. Recent major developments in polymer-electrolyte membrane…
Abstract Summary: Polyaniline‐dodecybenzenesulfonic acid (PANI‐DBSA)/epoxy resin (EP) blends were prepared by a solution‐in‐toluene process and direct mixing of PANI‐DBSA with EP. The dispersion quality of PANI‐DBSA proved to be strongly related to the final electrical properties of the cured blends. The solution proc…
Brominated epoxy resins cured with diaminodiphenyl sulfone are thermally less stable than nonbrominated analogs. This thermal instability is likely to be caused by the formation of hydrogen bromide which destabilizes the epoxy network. As a result of the reaction of HBr with the epoxy resin, bromine-containing aromati…
Abstract Summary: Energy‐filtering transmission electron microscopy (EFTEM) was employed for the analysis of polymer‐polymer interfaces. To attain imaging and spectral analyses with a spatial resolution of 10 nm, problems arising in the EFTEM analysis for polymer specimens were investigated. Interfaces in poly(methyl…
Abstract Blends of poly(butylene terephthalate) (PBT) with 30 wt % acrylonitrile–ethylene–propylene–diene–styrene (AES) were prepared with methyl methacrylate (MMA)/glycidyl methacrylate (GMA)/ethyl acrylate (EA) terpolymers (MGEs) as compatibilizing agents. These acrylic terpolymers were miscible with the styrene–acr…
In this work the piezoresponse mode of the atomic force microscope has been applied for piezoelectric coefficient measurements in nanometer scale in high conductive RbTiOPO4 and KTiOPO4 ferroelectric crystals with specifically tailored domain configurations. A strong dependence of the amplitude and phase contrast betw…
Abstract Insoluble fibroin films were prepared without methanol treatment. A 15 wt % fibroin solution was obtained through concentration, and then, the insoluble film was achieved by the adjustment of the drying temperature and rate. These films were examined through Fourier transform infrared–attenuated total reflect…
A comprehensive discussion on the flammability of organic-inorganic nano-composites is presented based on different fire testing methods. Based on various flammability tests, reduced peak heat release rate, an increased oxygen index, and an enhanced thermal stability were observed, while faster burning rates were foun…
Single phase powders of BaTi2O5 and Ba6Ti17O40 were made by a sol-gel method with final heating at 1100–1200°C. Ceramic samples were prepared and fired at temperatures in the range 1100–1300°C. Both sets were highly insulating, with conductivities of, e.g., 10−6–10−7Scm−1 at 600°C and activation energies for conductio…
Abstract Summary: Blends of polyamide‐6 (PA6) and low density polyethylene (LDPE) were compatibilized by melt mixing with various polyolefins functionalized with glycidyl methacrylate (GMA), i.e., GMA grafted LDPE (LDPE‐ g ‐GMA), GMA grafted styrene‐ethylene/butylene‐styrene block copolymer (SEBS‐ g ‐GMA) and ethylene…
Ceramics of composition Bi3TiNbO9 (BTN) and perovskite-layered structure (Aurivillius type) [B. Aurivillius, Ark. Kemi 1, 463 (1949)] were processed by natural sintering and hot pressing from amorphous precursors. Precursors were obtained by mechanochemical activation of stoichiometric mixtures of oxides. These materi…
Analytical ultracentrifugation (AU) provides a general way to probe the polydispersity of nanoparticles and the formation of bioconjugates in solution. Unconjugated gold nanocrystals show sedimentation coefficient distributions that are in agreement with size distributions as measured by TEM. AU is sensitive to the si…
Dielectric response and electrical conduction properties of 0.94Pb(Fe1∕2Nb1∕2)O3–0.06PbTiO3 single crystals grown by the Bridgman method were studied. It was found that the single crystals did not show any sign of the presence of Curie temperature between room temperature and 300 °C. However, they exhibited very high…
Abstract Poly(ethylene terephthalate) (PET) and PET/montmorillonite(MMT) (2.5 wt %) nanocomposites with high molecular weight were prepared by solid‐state polycondensation and their fiber was spun and drawn under various conditions. The influence of MMT nanomaterials on the thermal shrinkage of PET fiber was investiga…
Effects of pulsed and continuous light illumination on field emission from CuO nanobelt arrays have been studied by using a transparent anode technique. It is found that, at low-field emission current level, the field emission current generally increases under a pulsed irradiation; at an emission current level of 1.1μ…