Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
In this paper we discuss the microstructure of lath martensitic steels and the mechanisms by which it controls cleavage fracture. The specific experimental example is a 9Ni (9 wt% Ni) steel annealed to have a large prior austenite grain size, then examined and tested in the as-quenched condition to produce a relativel…
A porous β-tricalcium phosphate (β-TCP) bioceramic scaffold was successfully prepared with our homemade selective laser sintering system. Microstructure observation by a scanning electron microscope showed that the grains grew from 0.21 to 1.32 μm with the decrease of laser scanning speed from 250 to 50 mm min−1. The…
We report on the stress-induced growth of Au microwires out of a surrounding Au–W matrix by selective oxidation, in view of a possible application as 'micro-Velcro'. The Au wires are extruded due to the high compressive stress in the tungsten oxide formed by oxidation of elemental W. The samples were fabricated as a t…
This paper studies boron precipitation and segregation at austenitic grain boundaries for low carbon boron steels types: PL22 and 15BCr30. The following parameters were evaluated: percentage of martensite/bainite, size and nucleation sites of austenitic grains and precipitates sizes. Three austenitization temperatures…
In this paper the design of experiment method is used to investigate and explain the effects of the rotor parameters on crack breathing and propagation in the shaft. Three factors are considered which have an influence on the behavior and the propagation of the crack: the rotational speed, the length of the rotor and…
It was recently shown that the crystallinity of extracted bone mineral samples from the fin bones of zebrafish could increase over storage time. This would have implications in many studies in which the samples need to be stored until analysis. The aim of this study was to further evaluate if the crystallinity of extr…
The complex dielectric permittivity (ε) and magnetic permeability (µ) of Radar Absorbing Materials (RAM) based on magnetic particles (MnZn ferrite particles) embedded in a dielectric matrix (silicon rubber) have been studied in the frequency range of 2 to 18 GHz. The relative permeability and permittivity of MnZn ferr…
Self-compacting mortar (SCM) is a new generation product and has prospective use as an independent material as well as an integral constituent of self-compacting concrete (SCC). In this paper the flow response of self-compacting mortar is assessed by Taguchi method and ANOVA interaction. Effect of powder material and…
When AISI 316L stainless steels are submitted to the nitriding process at temperatures lower than 450 °C, a high nitrogen content expanded austenite phase is formed, which shows higher hardness and higher pitting corrosion resistance compared to the untreated material. As a result, this material becomes adequate for b…
We present our recent results on Pt nanoparticles on graphene sheets (Pt-NPs/G), a nanocomposite prepared with microwave assistance in ionic liquid 2-hydroxyethanaminiumformate. Preparation of Pt-NPs/G was achieved without the addition of extra reductant such as hydrazine or ethylene glycol. The Pt nanoparticles on gr…
This study presents an experimental investigation on surface roughness and chip formation in turning of Al 2219/15SiCp and Al 2219/15SiCp-3Gr (hybrid) composites. Experiments were conducted with different cutting conditions using carbide, coated carbide and polycrystalline diamond (PCD) tools. The results reveal that…
Composites of polydiphenylamine (D-PDPA) and zeolite Y with H+ as the cation (Y_H+) have been fabricated to be used as a sensing material towards non-halogenated and halogenated solvents (hexane, dichloromethane, 1, 2-dichloroethane, chloroform). These composites are toxic towards human and environment and are widely…
A tissue-engineered endothelial layer was prepared by culturing endothelial cells on a fibroblast growth factor-2 (FGF-2)–l-ascorbic acid phosphate magnesium salt n-hydrate (AsMg)–apatite (Ap) coated titanium plate. The FGF-2–AsMg–Ap coated Ti plate was prepared by immersing a Ti plate in supersaturated calcium phosph…
Scaffolds were fabricated by electrospinning using polycaprolactone (PCL) blended with poly(methyl methacrylate) (PMMA) in ratios of 10/0, 7/3, 5/5 and 3/7. The PCL/PMMA ratio affected the fiber diameter, contact angle, tensile strength and biological in vitro and in vivo properties of the scaffolds, and the 7/3 ratio…
The aim of this work was the evaluation of the thermal-rectification process of reforestation wood Corymbia citriodora Hook by measuring of mechanical properties under compression parallel to the grain and also determining of chemical composition. The tested samples were thermally treated in a furnace with nitrogen-at…
Cell adhesion on materials surface is critical because this phenomenon occurs before other events, as cell spreading, cell migration and cell differentiation. it is commonly accepted that the adhesion of cells on solid substrate is influenced by several substratum surface properties, such as wettability, surface charg…
Stem cells are known for their potential to repair damaged tissues. The adhesion, growth and differentiation of stem cells are likely controlled by the surrounding microenvironment which contains both chemical and physical cues. Physical cues in the microenvironment, for example, nanotopography, were shown to play imp…
This paper reports the results of studies on the effect of aspect ratio of multiwall carbon nanotubes (CNT) on the shear and extensional rheological behavior of low density polyethylene (LDPE) nanocomposites. Up to a CNT loading of 2wt%, as used in the present study, the shear rheological data suggest no network forma…
The development of shape memory actuators has enabled noteworthy applications in the mechanical engineering, robotics, aerospace, and oil industries and in medicine. These applications have been targeted on miniaturization and taking full advantage of spaces. This article analyses a Ti-Ni shape memory actuator used as…
Tensile properties and fracture location of AA2139-T351 friction stir welded joints are studied in the as-welded and post-weld aged condition. The experimental results show that when the joints are free of welding defects, they fail on the advancing side of the HAZ exhibiting a large amount of plastic deformation. Whe…