Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
The aim of the present study was to evaluate the influence of different photopolymerization (halogen, halogen soft-start and LED) systems on shear bond strength (SBS) and marginal microleakage of composite resin restorations. Forty Class V cavities (enamel and dentin margins) were prepared for microleakage assessment,…
In this work, the static mechanical properties and cyclic fatigue life of 3 mol. (%) Y2O3-stabilized tetragonal zirconia polycrystalline (3Y-TZP) ceramics were investigated. Pre-sintered samples were sintered in air at 1600 °C for 120 minutes, and characterized by X ray diffraction and scanning electronic microscopy.…
Cold upsetting experiments were carried out on sintered Fe-0.8%C steel preforms in order to evaluate the technical relationship that exist between the applied stresses against continuous deformation and densification. Powder preforms of 86% theoretical density and 0.40 of initial aspect ratio were subjected to increme…
The purpose of this study was to establish whether material properties of elastin co-electrospun with polydioxanone (PDO) would change over time in both the uncross-linked state and the cross-linked state. First, uncross-linked scaffolds were placed in phosphate buffered saline (PBS) for three separate time periods: 1…
An experimental investigation of the effect of two different type of stitches viz., lockstitch and chainstitch at the seat seam of trouser for military armed forces has been reported. Performance of chainstitched seam is found to be much better as regards lower value of force at low level of strain, higher value of fo…
The ultrasonic phase velocity was measured on a high purity nickel single crystal with a bias magnetic field in cooling and heating runs over the interval of temperatures from approximately 100 to 325 K. An evident anomaly of the phase velocity was observed in both branches of the temperature cycle. The temperature of…
The determination of the microstructure and chemical composition of La0.7-xPr xMg0.3Al 0.3Mn0.4Co0.5 Ni3.8 (0 < x < 0.7) metal hydride alloys has been carried out using scanning electron microscopy (SEM), energy dispersive X ray analysis (EDX) and X ray diffraction analysis (XRD). The substitution of La with Pr change…
The objective of this work is to develop empirical models to predict end use properties of low density polyethylene (LDPE) resins as functions of two intrinsic properties easily measured in the polymers industry. The most important properties for application in the flexible plastic packaging industry were evaluated ex…
The influence of hot-band grain size and additions of aluminum and manganese on the magnetic properties of non-oriented grain (NOG) low-carbon electrical steel with about 3 wt. (%) Si were investigated using optical microscopy and X ray diffraction. The addition of manganese resulted in larger grains after final annea…
Silicon nitride based ceramics are promising candidates for biomedical applications due to their chemical and dimensional stability associated to suitable mechanical strength and relatively high fracture toughness. However, the bioinert characteristics of these ceramics limit their application to situations where the…
The influence of starting point microstructures on the transformation mechanisms and mechanical properties of a micro alloyed steel after annealing in the alpha + gamma region have been investigated. Three different microstructures: austenite, pearlite in a ferrite matrix and martensite were used as starting point mic…
The use of porous bioresorbable scaffolds in the field of tissue engineering represents an alternative for the treatment of lesions and losses of biological tissues. This work evaluates the leaching salt effect of two different processes and polymers. Dense and porous scaffolds were prepared with poly(epson-caprolacto…
The high temperature oxidation and erosion-oxidation (E-O) behavior of steels AISI 1020, 304, 310, and 410 were determined. These steels were selected to evaluate the effect of chromium content on its E-O resistance. The oxidation behavior was determined in a thermogravimetric analyzer. A test rig in which a specimen…
Antiseptic apatite-based calcium phosphates were prepared as the single-phase powders. Phosphocalcic oxygenated apatites were synthesized from calcium salts and orthophosphate dissolved in oxygenated water solution at 30%, under the biomimetic conditions of 37 °C and pH 7.4. The characterization and chemical analysis…
In this article, photothermal techniques were used in order to determine some thermal properties: diffusivity, conductivity, effusivity and specific heat capacity of WC-10 wt. (%) Co six samples subjected to different sintering processes. The samples were sintered using high pressure - high temperature (HPHT) sinterin…
A formal kinetic approach was applied to the spread of isothermal martensite over the neighboring austenite grains in a Fe-23.2 wt. (%) Ni-2.8 wt. (%) Mn alloy. The number of grains in a spread event changed with parent austenite grain size. However, isothermal martensite spread formed from fine-grained parent austeni…
In this paper, we present results from a computational fluid dynamics (CFD) model for the mixing process used to disperse synthetic fibers in wet-lay process. We used CFD software, FLUENT, together with the MIXSIM user interface to accurately model the impeller geometry. A multiple reference frame (MRF) model and stan…
Expanded poly(butadiene-co-styrene) (SBR), a residue of the shoe industry of Rio Grande do Sul, is a crosslinked material. For further utilization in recycling and reclaiming processes this residue was ground under ambient conditions. The obtained powder (SBR-r) was physically, thermally and chemically characterized a…