Materials Literature
按标题、摘要、年份、主题和来源检索公开元数据。结果保留作者、摘要、分类与原始来源链接。
Double-walled carbon nanotubes (DWCNTs) were synthesized by chemical vapour deposition using Fe–Mo catalyst supported on magnesium oxide particles. A mixture of gases of methane and hydrogen was used for the growth. The effect of gas pressure, ratio of methane to hydrogen, and growth temperature on the structure, puri…
The synthesis of PbFeO 2 F is achieved using a solid-state reaction under high pressure. This perovskite crystallizes in SG Pm 3̄ m (No. 221) with a = 0.39991 (1) nm. The Rietveld refinement using powder X-ray diffraction data shows that the mean structure of this compound can be characterized as follows: (1) the Pb i…
Polychromatic X-ray microdiffraction is an emerging tool for studying mesoscale structure and dynamics. Crystalline phase, orientation (texture), elastic and plastic strain can be nondestructively mapped in three dimensions with good spatial and angular resolution. Local crystallographic orientation can be determined…
An analytical technique that can be effectively used for the calculation of the end-winding leakage inductance of a turbogenerator has been presented. It is based on a three-dimensional geometric model of the end-winding region in which each coil is modeled as a set of serially connected straight filaments. The calcul…
A completely soluble polyaniline-multi-wall carbon nanotube (CNT-PANI) composite with drastically enhanced conductivity, improved thermal stability, and luminescent behaviour, has been synthesized. The presence of straight multi-wall carbon nanotubes during the polymerization of aniline induces the formation of a more…
Atomic cations (26), M+, have been shown to lie within a thermodynamic window for O-atom transport catalysis of the reduction of N2O by CO and have been checked for catalytic activity at room temperature with kinetic measurements using an inductively-coupled plasma/selected-ion flow tube (ICP/SIFT) tandem mass spectro…
Preparation and characterization of europium(III), terbium(III), samarium(III), and dysprosium(III) polystyrene nanoparticle labels with lanthanide-specific fluorescence properties has been presented. Emulsion copolymerization of styrene and acrylic acid was used to synthesize uniform-sized nanoparticles approximately…
BACKGROUND: Magnetic fluid hyperthermia (MFH) is a new technique for interstitial hyperthermia or thermoablation based on AC magnetic field-induced excitation of biocompatible superparamagnetic nanoparticles. Preliminary studies in the Dunning tumor model of prostate cancer have demonstrated the feasibility of MFH in…
We report the characterization of strain components in transistor structures with silicon–germanium (Si0.75Ge0.25) and silicon–carbon (Si0.99C0.01) stressors grown by selective epitaxy in the source and drain regions. The spacing between the source and drain stressors is 35nm. Lattice strain analysis was performed usi…
Phase formation of surface alloying by spinodal decomposition has been studied at an electrified interface. For this aim Zn was electrodeposited on Au(111) from the ionic liquid AlCl(3)-MBIC (58:42) containing 1 mM Zn(II) at different potentials in the underpotential range corresponding to submonolayer up to monolayer…
We have realized highly efficient photodetectors based on composites of the semiconducting polymer poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] and PbSe nanocrystal quantum dots. The external quantum efficiency in these devices is greater than 1 for electric fields E∼7×105V∕cm. The observed photocurrent…
Li2Pd3B is known to be superconducting, while the isotypical Li2Pt3B compound is not. Electronic structures of Li2Pd3B and Li2Pt3B have been calculated in order to obtain an insight into this surprising difference, through an analysis of the differences in the band structures. The electronic structures of these system…
Evidence for a strong spin-lattice coupling in multiferroic $\mathrm{Ho}\mathrm{Mn}{\mathrm{O}}_{3}$ is derived from thermal expansion measurements along the $a$ and $c$ axes. The magnetoelastic effect results in sizable anomalies of the thermal expansivities at the antiferromagnetic $({T}_{N})$ and the spin rotation…
Resistive transitions of an epitaxial Bi$_2$Sr$_2$CaCu$_2$O$_{8+δ}$ thin film were measured in various magnetic fields ($H\parallel c$), ranging from 0 to 22.0 T. Rounded curvatures of low resistivity tails are observed in Arrhenius plot and considered to relate to deviations from plastic barriers. In order to charact…
Prediction and characterization of crystal structures of alloys are a key problem in materials research. Using high-throughput ab initio calculations we explore the low-temperature phase diagrams for the following systems: {Bi-In, Bi-Mg, Bi-Sb, In-Mg, In-Sb, and Mg-Sb}. For the experimentally observed phases in these…
Carbon nanotubes have interesting electromechanical properties that may enable a new class of nanoscale mechanical sensors. We fabricated two-terminal nanotube devices on silicon nitride membranes, measured their electronic transport versus strain, and estimated their band gaps and the strain-induced changes in them.…
We report the synthesis of a single-walled carbon nanotube (SWNT) graft copolymer. This polymer was prepared by the functionalization of SWNTs with polyethyleneimine (PEI). We used this graft copolymer, SWNT-PEI, as a substrate for cultured neurons and found that it promotes neurite outgrowth and branching.
We predict the occurrence of large ferroelectric polarization and piezoelectricity in the hypothetical perovskite-structure oxides, bismuth aluminate (BiAlO 3 ) and bismuth gallate (BiGaO 3 ), using density functional theory within the local density approximation. We show that BiGaO 3 will have a similar structure to…
We report a chemical processing technology that allows the continuous spinning of single-walled carbon nanotubes (SWNTs)-nylon 6 (PA6) fibers by the in-situ polymerization of caprolactam in the presence of SWNTs, which simultaneously optimizes the morphology of the composite. We show that caprolactam is an excellent s…
Flexible polyurethane foam is often molded directly into preheated tools for foaming reaction which expands to fill the mold cavity. The foam that is directly in contact with the mold surface cures as the foam skin. Parts frequently have surface defects ranging from shrink marks, to voids, to mottling, and knit lines.…